The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service

Dynamic Green Products Inc.





Author Topic: Help to ID this Machinery  (Read 3509 times)

0 Members and 1 Guest are viewing this topic.

Offline OldIronMan

  • member
  • *
  • Posts: 24
  • Age: 60
  • Location: South Lyon, Michigan
  • Gender: Male
    • Share Post
    • Antique Wind Mills
Re: Help to ID this Machinery
« Reply #20 on: July 28, 2011, 07:41:12 AM »
You must have relocated it and cleaned up the iron - it looks refurbished. I don't see any trees growing up through the spokes. ;)

Yes I think someone relocated it years ago.  I know it's been in this spot for the past 30 years anyway.  It's sitting on a power line hence the lack of trees under it.  For the iron, I think it has a high percentage of iron and low in carbon, much like wrought iron which doesn't rust as much as the metal you see today.
Work hard...play hard...

Offline mad murdock

  • Senior Member x2
  • *****
  • Posts: 3526
  • Age: 56
  • Location: NW OREGON Near Carlton.
  • Gender: Male
  • The woods is the best "office"!
    • Share Post
Re: Help to ID this Machinery
« Reply #21 on: July 28, 2011, 02:42:08 PM »
I drove by what used to be the foundry, on Sunday, on my way to fish. One of the many businesses that have gone under in Marion.
Prolly the same Marion of steam shovel fame?  I bet so. 
Turbosawmill M6 (now M8) Warrior Ultra liteweight, Granberg Alaskan III, lots of saws-gas powered and human powered :D

Offline timbuck2

  • Full Member x2
  • ***
  • Posts: 131
  • Location: In the heart of the White Mts, Lancaster NH
    • Share Post
Re: Help to ID this Machinery
« Reply #22 on: July 28, 2011, 06:17:11 PM »
Early Timberjack wheel???  ha

Offline Ron Scott

  • Forester
  • Administrator
  • *****
  • Posts: 8295
  • Age: 85
  • Location: Cadillac, MI
  • Gender: Male
    • Share Post
Re: Help to ID this Machinery
« Reply #23 on: July 28, 2011, 07:34:19 PM »
With the Marion foundry famous for is steam shovels and now out of business, I'd say that it is the winch wheel from one of their early stream shovels.
~Ron

Offline shelbycharger400

  • Senior Member x2
  • *****
  • Posts: 1399
  • Age: 39
  • Location: Becker mn
  • Gender: Male
  • m14/04 0
    • Share Post
Re: Help to ID this Machinery
« Reply #24 on: July 28, 2011, 09:44:43 PM »
all that old metal   has very high content of nickel and magnesium.    some of the best alloys .   now a days is basically "good" but not .              i remember reading a deal about the ww1/ww2 tanks.  the alloys were such that you had a very hard time torch cutting them ect,  were so hard , and thick that it was cheaper to sink them off the coast.       also,  noted that 1960's and back, automobiels, most scrap yards cannot send them through their shredder, its along same deal.

Offline tyb525

  • Senior Member x2
  • *****
  • Posts: 3368
  • Age: 28
  • Location: Eastern Indiana
  • Gender: Male
  • Always learning.
    • Share Post
Re: Help to ID this Machinery
« Reply #25 on: July 28, 2011, 11:43:56 PM »
The fishing was alright, we waded out to the middle of the river right below the old dam. caught a bunch of small crappies and carp, and a friend caught what we think was a big crappie, about 2ft long. It got away right as we were pulling it out of the water, it must've just barely got the hook.

There's a lot of history around here, wish there were more records and pictures of it. The town I live nearest to, Matthews, nearly became the state capital during the natural gas boom at the turn of the century, now it is home to no more than 600 people, and most of the old hotels and businesses are gone, all that's left is a small book covering some of the history, and stories from the few that can remember that time.

Anyways, sorry for hijacking the thread, back to the main topic!
LT10G10, Stihl 038 Magnum, many woodworking tools. Currently a farm service applicator, trying to find time to saw!


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Old Machinery

Started by iffy on Sawmills and Milling

2 Replies
1402 Views
Last post October 14, 2011, 10:43:52 AM
by inwoodcutter
xx
Used Machinery Sales

Started by RalphV on Job Opportunities

0 Replies
1316 Views
Last post August 30, 2011, 12:50:16 PM
by RalphV
xx
Vintage Machinery

Started by den on Sawmills and Milling

0 Replies
735 Views
Last post March 24, 2012, 10:55:22 PM
by den
xx
Identify this old machinery

Started by VooDooChikin04 on General Woodworking

8 Replies
727 Views
Last post May 16, 2020, 10:44:36 AM
by Rob in WNY
 


Powered by EzPortal